China Standard Heavy Duty 13m 3 Axle Side Wall Cargo Van Semi Truck Trailer with Best Sales

Product Description

13m 3 Axle Aspect Wall Cargo Van Semi-Trailer

1) Producer, far more than 20yrs professional experience. 
two) CCC, SGS and ISO9001 certificate 
three) Little buy can be accepted. 
four) Any shade and brand will be accessible. 
five) Products can be custom made-manufactured according to your design, or diversified wants. 

1.Chassis/The Major Beam ( 13000*2480* 3100mm)

A. Hefty duty and additional sturdiness designed, Higher plate16*140 mm, decrease plate  20*140 mm, ventral shield  8 mm, I beam 500 mm peak.  , Opting for higher tensile steel Q345B,  Side beam eighteen#,  Floor Steel 3mm. MASS:60T                                                                                                                     
two. Operating gear 
A. king pin: 90# ” king pin bolted type, 
B. Landing equipment: JOST C200 guide hefty duty landing gear 1 established. Ability: 28T
C. Axle:  three  Units FUHEL1(brand) fashion 10 hole 16 Ton axle 
D. L1 German stye mechanical 3 axle suspension. Suspension:  Leaf spring  one hundred* 14mm*14pcs  
E,  13 units of 13R22.5 Tubeless Tyre( brand appropriately),  13 units of 9.75*22.5 Wheel rim3. Brakes WABCO brand RE- 6 relay valve FOUR  units of T30/thirty spring brake chamber,Two models of T30 spring brake chamber. 2 models of dependable regional model common coppery air-connector,  TWO units of trustworthy local brand 40  air tank.4. Electric powered
Global common 24v circuit 7-pin ISO socket Tail lamp with switch signal, brake mild & reflector, facet lamp and so on. One established 6-core common Cable.

five. Painting
Sand blasting processing cleanse rust, 1 coat of anticorrosive primer, 2 coats of complete urethane paint, colour:   at your selection                          

A. One spare tyre holder, and 1 toolbox, and some 1200L oil tank.


Cut the rear part of the trailer, load it in to 40HQ container, 1 container carry 2 units, and fit it by screw in destination by customer.

Payment conditions:
T/T thirty% as deposit in progress ahead of manufacturing, and T/T 70% equilibrium soon after buyer check out the goods and just before shipping.
3. Validity of Proforma Invoice: thirty Times

How to Recognize a Defective Drive Shaft

The most frequent troubles connected with automotive driveshafts incorporate clicking and rubbing noises. Whilst driving, the sound from the driver’s seat is often apparent. An seasoned car mechanic can very easily determine whether the sound is coming from each sides or from a single aspect. If you observe any of these symptoms, it is time to send out your vehicle in for a appropriate prognosis. This is a manual to identifying if your car’s driveshaft is faulty:

Symptoms of Driveshaft Failure

If you’re obtaining problems turning your car, it is time to check your vehicle’s driveshaft. A poor driveshaft can restrict the all round management of your vehicle, and you need to correct it as shortly as possible to steer clear of more problems. Other indicators of a propshaft failure include strange noises from under the automobile and trouble shifting gears. Squeaking from under the car is another indication of a faulty driveshaft.
If your driveshaft fails, your car will stop. Though the engine will nonetheless run, the wheels will not change. You may possibly hear unusual noises from beneath the motor vehicle, but this is a uncommon symptom of a propshaft failure. Nevertheless, you will have loads of time to resolve the problem. If you do not listen to any noise, the difficulty is not impacting your vehicle’s ability to move.
The most clear indicators of a driveshaft failure are boring sounds, squeaks or vibrations. If the generate shaft is unbalanced, it is most likely to hurt the transmission. It will need a trailer to eliminate it from your vehicle. Aside from that, it can also influence your car’s efficiency and require repairs. So if you hear these signs in your auto, be positive to have it checked by a mechanic appropriate away.

Push shaft assembly

When designing a propshaft, the layout must be based on the torque needed to push the vehicle. When this torque is also substantial, it can cause irreversible failure of the generate shaft. For that reason, a excellent generate shaft design must have a extended service lifestyle. Below are some ideas to support you layout a excellent driveshaft. Some of the primary components of the driveshaft are detailed beneath.
Snap Ring: The snap ring is a detachable element that secures the bearing cup assembly in the yoke cross hole. It also has a groove for finding the snap ring. Spline: A spline is a patented tubular machined element with a sequence of ridges that suit into the grooves of the mating piece. The bearing cup assembly consists of a shaft and end fittings.
U-joint: U-joint is essential owing to the angular displacement amongst the T-shaped housing and the pinion. This angle is especially big in lifted 4x4s. The style of the U-joint should promise a consistent rotational velocity. Proper driveshaft layout need to account for the big difference in angular velocity among the shafts. The T-bracket and output shaft are hooked up to the bearing caps at equally finishes.


Your automobile has a established of U-joints on the driveshaft. If your vehicle needs to be replaced, you can do it oneself. You will need a hammer, ratchet and socket. In order to take away the U-joint, you need to initial get rid of the bearing cup. In some instances you will require to use a hammer to take away the bearing cup, you need to be cautious as you don’t want to hurt the drive shaft. If you can not take away the bearing cup, you can also use a vise to push it out.
There are two varieties of U-joints. 1 is held by a yoke and the other is held by a c-clamp. A entire ring is safer and best for autos that are frequently used off-road. In some situations, a full circle can be utilised to mend a c-clamp u-joint.
In addition to too much torque, extreme hundreds and inappropriate lubrication are typical triggers of U-joint failure. The U-joint on the driveshaft can also be broken if the motor is modified. If you are driving a motor vehicle with a greatly modified motor, it is not adequate to change the OE U-joint. In this situation, it is important to consider the time to appropriately lubricate these factors as essential to preserve them functional.

tube yoke

QU40866 Tube Yoke is a typical substitution for damaged or ruined driveshaft tubes. They are desirably created of a metallic substance, this kind of as an aluminum alloy, and consist of a hollow part with a lug composition at one particular conclude. Tube yokes can be created making use of a range of strategies, like casting and forging. A typical technique entails drawing sound aspects and machining them into the ultimate condition. The resulting factors are considerably less costly to generate, specially when compared to other types.
The tube fork has a relationship point to the driveshaft tube. The lug structure supplies attachment factors for the gimbal. Normally, the driveshaft tube is 5 inches in diameter and the lug structure is 4 inches in diameter. The lug composition also serves as a mounting stage for the drive shaft. After set up, Tube Yoke is easy to maintain. There are two kinds of lug buildings: 1 is solid tube yoke and the other is welded.
Large-obligation series generate shafts use bearing plates to safe the yoke to the U-joint. All other proportions are secured with external snap rings. Yokes are usually machined to take U-bolts. For some apps, grease fittings are used. This attachment is a lot more suited for off-highway automobiles and performance vehicles.

end yoke

The end yoke of the travel shaft is an integral portion of the push practice. Deciding on a higher-top quality conclude yoke will assist make certain long-time period procedure and avoid untimely failure. Pat’s Driveline delivers a complete line of automotive finish yokes for energy consider-offs, differentials and auxiliary equipment. They can also measure your present areas and give you with large quality replacements.
A U-bolt is an industrial fastener with threaded legs. When utilized on a driveshaft, it supplies higher stability in unstable terrain. You can obtain a U-bolt package to safe the pinion provider to the generate shaft. U-bolts also arrive with lock washers and nuts. Functionality autos and off-street cars frequently use this variety of attachment. But just before you set up it, you have to make confident the yoke is machined to take it.
Finish yokes can be manufactured of aluminum or steel and are made to offer energy. It also delivers special bolt styles for various programs. CZPT’s drivetrain is also stocked with a total line of automotive flange yokes. The business also generates custom made flanged yokes for many well-liked makes. Because the organization has a thorough line of substitute flange yokes, it can aid you rework your drivetrain from non-serviceable to serviceable.


The first action in repairing or replacing an automotive driveshaft is to replace worn or damaged bushings. These bushings are situated inside the generate shaft to supply a clean, secure trip. The shaft rotates in a rubber sleeve. If a bushing wants to be changed, you must very first check out the guide for recommendations. Some of these elements might also need to have to be changed, this sort of as the clutch or swingarm.

China Standard Heavy Duty 13m 3 Axle Side Wall Cargo Van Semi Truck Trailer     with Greatest Product salesChina Standard Heavy Duty 13m 3 Axle Aspect Wall Cargo Van Semi Truck Trailer     with Very best Sales


Recent Posts